Structured Cabling
Cat6/Cat6A cabling, patch panels and Fluke certification, labeled and documented.
- Covers
- Cat6 / Cat6APatch panelsCable traysFluke certificationLabelling & as-builts
- Options
- Cat6 · Cat6A · Fiber backbone · Shielded (F/UTP)
- How we work
- Survey → Design → Install → Certify → Hand over
Nobody knows which cable goes where, so simple moves take hours. Our fix: Dressed racks and labels at both ends.
See the common problemsPoor terminations cause drops that look like "network problems". Our fix: Certified links with test reports.
See the common problemsContractors left without as-builts or test results. Our fix: As-built drawings and a full port map.
See the common problemsRough quantities for outlets, cable and patch panels.
Try the cabling estimatorAnswer a few quick questions and a Skylius specialist will prepare practical recommendations.
Request a consultationUnlabelled cables turn every fault into a hunt.
Cat6 and Cat6A structured cabling, patch panels and cable management, certified link by link and documented so any port can be traced in seconds.
Sound familiar?
What bad cabling costs you.
Cable spaghetti
Nobody knows which cable goes where, so simple moves take hours.
Intermittent faults
Poor terminations cause drops that look like "network problems".
Can't support new tech
Old cabling can't carry 2.5G Wi-Fi or high-power PoE.
No drawings
Contractors left without as-builts or test results.
What we deliver
Everything included, end to end.
Outlet positions, routes, containment and rack layout.
Trays, conduits and trunking installed neatly to standard.
Cat6/Cat6A cable pulled, terminated and dressed.
Panels, organisers and patch leads with colour coding.
Every link tested with a certifier and reports issued.
Labels at both ends, port map and drawings.
Key options & specs
Choose what fits your site.
Cat6
1 Gbps everywhere, 10 Gbps on short runs. Cost-effective.
Cat6A
10 Gbps to 100 m and better heat handling for high-power PoE.
Fiber backbone
Multi-mode or single-mode for long and high-capacity links.
Shielded (F/UTP)
Better immunity near motors, MEP plant and industrial equipment.
Interactive · cabling estimator
Estimate your cabling scope.
Rough quantities for outlets, cable and patch panels.
Indicative result
Indicative only. Includes 10% waste allowance. Final quantities follow a site survey and drawings.
Send this on WhatsAppHow we work
A clear process, no surprises.
Survey
Walk the site and mark outlets and routes.
Design
Drawings, containment and BOQ.
Install
Containment, pulling, termination and dressing.
Certify
Test every link and fix any failures.
Hand over
Labels, port map, test reports and as-builts.
Brands we work with
Proven platforms, chosen per project.
FAQ
Questions about Structured Cabling.
Have a different question? A specialist will reply on WhatsApp.
Not always. We survey and test the existing runs, keep what passes, and re-route or replace only failed or untidy sections, labelled to a clear scheme.
Every link is certified with a cable tester and you receive the test results per port, together with labelled floor plans and patch-panel schedules.
We agree working hours with you, keep work areas tidy and safe, and can work after hours or floor by floor so staff can keep working.
Cat6 suits most desks. Use Cat6A for Wi-Fi 6E/7 access points, high-power PoE and anywhere you want 10 Gbps for the long term.
Yes. Each permanent link is tested with a cable certifier and you receive the reports.
Yes. We re-patch, label and dress racks, usually out of hours to avoid disruption.
Well-installed structured cabling typically outlives two or three generations of network equipment.
Structured Cabling
Cabling done once, done right, documented.
Tell us about your site and requirements. We will review them and send a clear, itemised proposal.
